ASSOCIATION
OTTPA Garden Tractor Website
www.ottpagardentractors.ca
2017 CORPORATE SPONSORS

Stay tuned for our new corporate
sponsors for the
upcoming pull season
Registration: 12 PM
Start Time:  10 AM
Registration: 12 PM
Start Time:  10 AM
Schedule is posted on schedule page

2017  SCHEDULE
The upcoming season is fast approaching
Have a look and get your weekends all booked up
to attend OTTPA events near you and here some noise

Wet-Track Pulling Skills for Australian Competitors

Rain can turn a powerful truck pull into a test of patience, traction and sound decision-making. Tips for driving a puller on a wet or slick track are not about finding extra speed; they are about preserving control while still giving the sled an honest pull. A disciplined approach also protects the machine, the crew and everyone watching from the sidelines.

Wet-weather competition days often reward the driver who understands the surface rather than the driver who reacts hardest to it. Preparation begins with the forecast and continues through the track inspection, ballast decision, tyre setup and communication with officials. The same principles apply at regional Australian shows, where crews may travel long distances between venues and cannot easily replace a damaged component on competition day.

Why Water Changes the Run

A dry track gives the tyres a predictable connection with the ground. Water, soft clay or a greasy film of mud can interrupt that connection, especially as the sled transfers weight onto the rear axle. The tyres may spin, break loose or wander off the intended path. More power does not correct a traction problem; it usually magnifies it.

Australian weather can change with startling speed. A La Niña pattern may bring widespread rain and flooding, while an El Niño summer can alternate between dry heat and sudden coastal downpours. Inland tracks may already be soft from an earlier storm, then absorb more water during the event. At venues near the coast, salty air and persistent humidity can leave shaded sections damp when the main racing area appears dry.

The driver must also consider visibility, braking distance and the condition of the access roads. Rain reduces contrast, fills low points and turns compacted clay into a slippery surface. Standing water can hide holes, ruts and loose gravel. A pull that looks routine in daylight can become unpredictable as the track darkens, the moisture rises or drivers begin cutting tyre treads and disturbing the surface during earlier heats.

Practical Checks Before and During a Session

Begin with the official information for the event. The association’s pulling schedules and forms offer a useful reference for dates, registration details and safety information, although Australian competitors must confirm class rules, insurance requirements and track arrangements with the host club. Weather advice from the Bureau of Meteorology should be checked against local flood warnings and road closures.

Inspect the machine before loading it for the trip. Check the tyres for cuts, bulges and embedded objects, then look closely at the rims, wheel fasteners, suspension and steering components. Examine the tow chain, clevis, safety pins and drawbar hardware for wear or distortion. A machine that has worked hard on a dry track still needs attention after rain because mud can conceal cracks and trap moisture around critical fittings.

A useful pre-start routine is:

  • Follow the tyre pressures and ballast arrangement approved for the class and track.
  • Inspect the complete towing connection and confirm that every retaining device is fitted.
  • Check fluid levels, brakes, lights, battery condition and emergency shutoff systems.
  • Remove loose tools, hoses and stored water from the chassis before entering the track.

Once at the venue, use a second short checklist:

  • Walk the racing surface and identify standing water, deep ruts and soft shoulders.
  • Confirm the safe route back to the staging area with the track official.
  • Agree on hand signals or radio messages with the sled crew.
  • Stop and ask an experienced official whenever the track condition differs from the briefing.

Tyre pressure deserves particular attention because the correct setting changes with the surface. A softer tyre may place more rubber on the ground, but excessive pressure loss can overheat the sidewall during a long pull. Likewise, a muddy tread can lose its bite after several runs. Use the setup developed by an experienced crew rather than copying a pressure written for a dry day.

Read the Track Before Full Throttle

Inspect the track from more than one position. Look from the staging area towards the sled and then view the same section from the side. The lowest, wettest area is often easy to miss when every driver is following the same path. Watch how earlier competitors behave: repeated tyre spin, wandering hooks or deep slots in the clay show where traction has become unreliable.

Choose the line that offers the firmest surface and remains visible from the cab. Avoid crossing deep ruts at an angle, since that can unload one set of tyres and rotate the machine towards the barrier. Puddles should be treated as hidden changes in traction rather than harmless patches of water. If no clean line exists, the sensible move is to request a track adjustment or accept a reduced pull.

Ballast and hitch setup require experienced input. Moving weight can change stability and the way the rear tyres load, while the wrong hitch height can make the machine surge, rise or steer unpredictably. Changes should be made with the sled detached, according to the class rules and the vehicle builder’s recommendations. Never alter the setup during a run simply because the first few metres felt unusual.

Communication is especially valuable when conditions deteriorate. The sled driver, track official and pulling crew should know who has authority to stop a run. A clear signal from the official should override a driver’s determination to continue. Drivers who cannot see the entire track should have an agreed signal for hidden holes, standing water or a stopped sled.

Keep the Machine Moving in Control

A wet-track pull needs smoothness. Apply power progressively and watch what the rear tyres are doing instead of staring only at the sled. If the tyres begin to spin, ease off rather than adding more throttle. A small reduction in engine speed can restore enough grip for the drawbar to settle and the sled to move cleanly.

When traction breaks away, resist the urge to make a sharp steering correction. The machine may be sliding because the front tyres have entered a rut, because the load has shifted or because the track surface has changed. Lift off gently, straighten the machine and allow the tyres to find grip again. Sudden inputs can turn a recoverable slide into a spin, particularly on clay that has been polished by previous runs.

If the machine bogs or the sled stops, the driver should follow the official’s instructions rather than trying to build momentum through wheelspin. Stop, secure the machine and wait for assistance. Do not attempt to reverse across the active track without a clear hand signal, and keep spectators away whenever equipment is being recovered. A heavy puller carrying several tonnes becomes especially difficult to control when its forward movement is suddenly lost.

Mental discipline matters as much as mechanical control. Rain can encourage a driver to push harder because the sled feels lighter, yet this mindset often reduces traction and increases stress on the driveline. Stay within the limits established during practice, keep the same smooth inputs for every run and accept that a lower result on a saturated track is safer than a damaged machine or a trip to hospital.

Use Local Knowledge and Protect the Event

Australian truck and tractor pulling is closely tied to regional shows, agricultural communities and volunteer-run clubs. Competitors may travel between centres such as Orange in New South South, Hamilton in Victoria, Toowoomba in Queensland and Bundaberg in Queensland, adapting to the rules and track preparation used by each host organisation. Local sponsors, workshops and club members often supply the practical support that keeps a team competing.

Transporting a pulling machine adds another layer of planning. Australian traffic keeps left, distances are measured in kilometres and speed limits are posted in kilometres per hour. A wide puller may need an escort, oversize transport approval and a suitable route across bitumen and gravel roads. After rain, access roads can become corrugated, soft or closed, so crews should confirm the route before leaving home and allow more time than they would on a dry trip.

Local language also matters. A “pull” is a competition run, and the sled is sometimes called a pulling sled or a weight transfer sled. Some regulars simply call the driver a “puller”, while a team may refer to the event as a “shove”. Clear language remains essential because a crew member interpreting “give it a rev” differently from the driver could create unnecessary risk.

Keep a second channel for last-minute information. An online association news updates page can serve as a prompt to check for schedule changes, but the Australian event organiser’s own channels should be the authority on weather delays, track closure and running orders. Follow official instructions, support the volunteer crew and respect the barriers.

Make careful preparation part of every run: check the forecast, inspect the surface, confirm the setup and communicate clearly before applying power. Then drive the wet track with patience, control and respect for the people sharing the ground.

T EST and TUNE
May 20th @ Dan Fair
1208 Sharpe Line, Cavan
Contact Dan @ 705-930-4594
Food will be provided, so plan to attend