ASSOCIATION
OTTPA Garden Tractor Website
www.ottpagardentractors.ca
2017 CORPORATE SPONSORS

Stay tuned for our new corporate
sponsors for the
upcoming pull season
Registration: 12 PM
Start Time:  10 AM
Registration: 12 PM
Start Time:  10 AM
Schedule is posted on schedule page

2017  SCHEDULE
The upcoming season is fast approaching
Have a look and get your weekends all booked up
to attend OTTPA events near you and here some noise

Fixing a Leaky Hydraulic Line on Your Pulling Sled

A hydraulic leak on a pulling sled can be more troublesome than a puddle of oil under the machine. A weeping connection may reduce pressure, make controls sluggish or spray the hose, frame and hot exhaust. The repair depends on where fluid is escaping: the hose body, crimped end, fitting or seal. Identify the circuit, remove the energy source and replace the failed component rather than hide it with tape or a temporary clamp.

Australian pullers face hot, dusty ovals, corrugated roads and long runs between towns. A ute carrying the sled, spare fittings and a call to a regional hydraulic hose supplier can mean the difference between a minor repair and a missed class. Workshops commonly stock metric BSP fittings alongside SAE adapters, so check the thread style before buying. Keep the manufacturer’s diagrams and event safety notes handy, and use a qualified fitter for unfamiliar pressure or braking arrangements.

Trace the leak and make it safe

Find the leak before replacing anything. Clean and dry the hose, fittings and frame, then run the circuit only as far as the manufacturer permits while watching for mist, bubbling, a moving crimp or a wet trail. A fine mist is harder to see in dust or against a polished rim. If the pump loses pressure, the ram feels sluggish or the line heats, stop. Continuing with a split pressure line risks sudden failure and wasted fluid.

Make the machine safe before opening a connection. Follow the sled manual for the shutdown sequence: switch off the engine and pump, isolate the power source, lower or support any loaded ram or moving assembly, open the designated relief valve, and discharge accumulators or stored pressure. Use the manufacturer’s gauge or a properly rated test method to confirm the circuit is at zero pressure; never assume a closed valve has done that. Hydraulic fluid under pressure can penetrate skin and can release from a fitting with enough force to cause serious injury.

Once pressure is gone, inspect the route. A leak at a nut can mean a loose connection, damaged thread or failed O-ring. Fluid on the cover may point to abrasion against a bracket; a wet crimp can mean the hose or fitting failed. A quick choosing suitable hose check helps avoid the wrong size. A low-pressure connection may need only a seal, while a damaged pressure line needs the hose or fitting assembly replaced. Use a catch tray and keep hands away.

Match the hose, fittings and seals

Choose the replacement for the circuit, not for the shelf it came from. Check the hose’s working-pressure rating, burst pressure, fluid compatibility, temperature range, inside diameter, overall length and minimum bend radius. The line may carry more pressure in one direction than the other, and the pump may produce a sharp pressure spike when the sled load changes. Use the same rating or a higher one approved by the sled manufacturer, and never use an ordinary garden hose, a fuel line or a fuel-rated clamp as a substitute.

Before ordering, reading hydraulic hose markings is worthwhile because the print on a hydraulic hose can tell you its type, construction, size and pressure rating. Common markings include SAE, DIN or EN standards, working and burst pressure, dimensions and a manufacture date. Colours such as red, black or blue are not a universal specification, and a date code cannot replace the pressure information. If the marking is missing or unreadable, take the old hose to a supplier and ask for a matched replacement rather than guessing.

Fittings matter too. Metric BSP parallel thread, SAE straight thread with an O-ring and tapered NPT each seal differently, and Australian suppliers may stock several styles. Confirm thread size, seat angle, seal type and hose diameter. Do not force a fitting or use thread tape where an O-ring is specified; use the prescribed sealant and torque. Suppliers in Toowoomba, Bundaberg, Gunnedah or Shepparton can make a line to length. Give them fitting details and pressure information, not just outside diameter.

Replace the damaged line safely

At the track, make the repair in a controlled order. Photograph the hose route, mark its orientation, then drain and isolate the circuit according to the manual. Remove the damaged hose carefully, cover both ports immediately and wipe the fittings clean. A factory-crimped hose should normally be replaced as an assembly rather than pried apart; a reusable fitting can be inspected and cleaned only if it is in good condition and the manufacturer permits reuse. Keep the ports plugged until the new line is ready.

Fit the hose without twisting it. Slide it onto the fitting far enough to cover the sealing surface, verify the ferrule cannot bottom out and check connector alignment. Hand-fit the thread, then use specified torque; difficulty starting can mean the wrong thread or damaged seat. Route with a generous bend radius and secure it so it cannot rub, pinch or twist. If crimping it yourself, use the correct die and equipment; otherwise let a hose supplier make it.

Know the limits of a field repair. A hose clamp, silicone tape, epoxy or an unsuitable sealant can give the appearance of a repair while leaving a high-pressure line unsafe. Clamps are acceptable only where the hose and sled manufacturer permits them, such as some low-pressure return or suction applications; they are not a general fix for a pressure line. A split hose or damaged crimp calls for replacement of the complete hose assembly. If only the fitting has failed, replace the fitting, its seal and any suspect hose section, then check the hose under pressure.

Plan for regional pulling. A failure may happen after the last supplier closes in a small town, and a courier may take a day to reach the track. Carry a correctly rated spare hose, matching fittings, seals and spanners in a sealed box on the ute. Keep the old fitting as a sample and ask a local hose shop to ‘have a look’ before buying adapters. If a safe repair is impossible, arrange a technician or transport the sled.

Test the repair and prepare the sled

Test in stages. Restore the specified fluid level, check the hose is clear of moving parts and put controls in neutral. With the pump isolated, inspect every connection. Apply normal operating pressure in a clear area while watching the gauge and whole hose. Keep your face, fingers and others out of the line, and use a shield or cardboard to catch mist without leaning over the fitting. Stop if a joint weeps or pressure drops; do not increase the load to hide a leak.

After the first run, let the line cool and inspect it again. Heat can make a loose fitting show its problem, while dust can hide a small spray. Wipe the area with an approved method, check that the hose has not softened, bulged or flattened, and look for fresh fluid along the crimps. Retighten a connection only to the specified torque and only if the seal or thread is sound. Record the hose specification, fitting type, date and test result in the sled’s service notes so you do not have to work it out again at the next meet.

Track-day kit and checks

Tools and spare parts

  • Correct-size spanners and a quality ring spanner for the fittings.
  • A pressure-rated hydraulic hose matched to the circuit, plus suitable hose protection.
  • Matching connectors, O-rings or seals in metric, SAE or NPT as required.
  • An approved leak detector, catch tray, gloves and clean rags.

Checks before the first run

  • Confirm fluid level, pump operation and pressure readings against the sled manual.
  • Inspect the hose route for abrasion, sharp edges, kinks and interference.
  • Recheck every fitting and look for mist with the machine running.
  • Note the repair and keep the spare parts accessible in the ute.

A short service log is worth more than a guess on a dusty track. It lets the next crew member know which hose is fitted, which tools are needed and whether the leak has returned after heat or load.

Symptom Likely trouble Sensible response
Weeping at a fitting Loose nut, damaged thread or failed seal Isolate pressure; check the manual torque and replace the seal or fitting if needed
Fine spray from the hose body Split, abrasion or bad crimp Replace the hose assembly; do not tape or clamp it
Swollen or kinked section Internal damage or incompatible hose Remove it from service and replace it
Sluggish controls or lost pressure Air, low fluid, cavitation or pump trouble Check fluid, leaks and pressure; call a technician if it persists

Ready for the next pull

Make another failure less likely. Keep lines away from exhaust heat, turbo plumbing, sharp edges and moving suspension, using proper clips to stop chafe. Check condition before every event, keep fluid clean and at the specified level. A spare line, correct fittings and a circuit diagram are sensible insurance for a sled travelling around Australia.

OTTPA’s schedules, event locations, registration information and safety notices can help you plan the practical side of a meet. A regional oval in Bundaberg, Toowoomba, Gunnedah or Shepparton may be a straightforward trip with a well-prepared ute, but a broken line can still leave you waiting for parts. Give yourself time to inspect the sled, attend the safety briefing and sort out any fuel or tyre issue before the first pull.

Long journeys also mean planning for the gaps between classes. Check fuel, accommodation and a secure place to leave the ute, and if you want a little entertainment while you wait, compare online pokies options before setting off. Keep the main focus on a safe, leak-free hydraulic system rather than treating downtime as part of the repair.

Before the next event, replace the damaged line, pack a correctly rated spare with matching fittings, and check the latest OTTPA notices. Arrive early, test in the paddock and fix anything that looks wrong. Turn up with a sealed circuit, a clear service record and a sled ready to pull.

T EST and TUNE
May 20th @ Dan Fair
1208 Sharpe Line, Cavan
Contact Dan @ 705-930-4594
Food will be provided, so plan to attend