|
ASSOCIATION
|
|
OTTPA Garden Tractor Website
www.ottpagardentractors.ca |
|
2017 CORPORATE SPONSORS
Stay tuned for our new corporate sponsors for the upcoming pull season |
|
Registration: 12 PM
Start Time: 10 AM |
|
Registration: 12 PM
Start Time: 10 AM |
|
Schedule is posted on schedule page
2017 SCHEDULE |
|
The upcoming season is fast approaching
Have a look and get your weekends all booked up to attend OTTPA events near you and here some noise |
Cleaning and maintaining your pulling vehicle after each event is about more than a hose-down and an oily rag. A competition run places heavy loads through the engine, drivetrain, chassis, wheels and safety equipment, often in conditions that trap dust, heat and vibration. A careful post-event routine can reveal a loose fastener, damaged tyre or developing leak before it becomes a failure at the next show.
Australian pullers face a distinctive mix of conditions. A truck may arrive on an ute tray, travel along corrugated roads and sit in the sun beside a rural showground. Summer afternoons can reach 40°C, while dust from the pull lane works its way into bearings and radiators. Working in metric, maintaining right-hand-drive road vehicles and dealing with imported left-hand-drive competition machines all add details that are worth checking after every run.
Begin with the engine and drivetrain at operating temperature, following the cooling procedure in the vehicle’s run book. A controlled idle or low-speed circulation can help the oil return to the sump and reduce sudden temperature changes in the engine. Avoid spraying cold water over a hot engine, radiator or exhaust, since thermal shock can crack components and distort heat-sensitive surfaces.
Watch the vehicle as it cools. Fresh oil around the filter housing, a coolant stain beneath the radiator, air bubbles in the overflow bottle or a rhythmic knock from the gearbox can all point to a problem that became noticeable under load. Fuel leaks need immediate attention, particularly around an open cab or hot exhaust. Switch off the engine, isolate the supply if necessary and keep ignition sources away before investigating.
Use the cool-down period to inspect rather than scrub. Look beneath the vehicle, note damaged hoses and check that guards are still secure. Keep the pull lane clear of spectators and bystanders while the hot exhaust, radiator and drivetrain remain exposed. A fire extinguisher, suitable gloves and basic eye protection should be close at hand.
Work from the upper areas of the engine bay towards the chassis, using a degreaser and brushes suited to the surfaces. The aim is to remove oil, rubber and packed dust without driving contaminants into seals, bearings or electrical connectors. Cover sensitive openings where practical and avoid directing high-pressure water at wheel bearings, steering joints, CV boots, ignition components or split pins.
Pay special attention to the area behind the front axle. Pulling transfers load through the front of a conventional truck or tractor, and this is where mud, stones and oil often collect. Clean the radiator core gently so the fins are not bent, clear debris from the air filter and inspect belts for glazing, fraying or contamination. A portable blower can help, provided it is used at a safe distance and not to spin exposed belt-driven components.
Fluid condition matters as much as fluid level. Check engine oil, coolant, transmission fluid, brake fluid and hydraulic oil against the manufacturer’s specifications. Look for water separated from diesel, cloudy gear oil or a rising oil level in the cooling system. A sample can be valuable when a leak is difficult to trace, but oil analysis should inform the service interval rather than replace sensible condition checks.
Used oil, coolant, oily rags and contaminated soil must not be tipped onto the ground or left near the showground. Use drums or containers with tight lids and follow the disposal rules of the local council or event organiser. Many rural Australian sites provide a designated waste area, so ask the ground crew before starting.
Inspect the chassis and mounting points for fresh cracks, movement around welds or distorted sections. Check every ballast bracket and fastener, especially where a truck’s weight box or tractor ballast frame attaches to the frame. Use the specified torque values and a calibrated wrench; a breaker bar can help you feel for a stubborn fastener, but it should never be used to overpower damaged or corroded hardware.
The drawbar, hitch and sled connection deserve the same attention as the engine. Look for wear around pins, bushings and bearing surfaces, then grease the parts specified by the manufacturer. Replace distorted washers, split pins and locking clips rather than bending them back into shape. If you are not sure whether a component is within its service limit, remove it from service and obtain advice from an experienced fabricator or scrutineer.
Ballast should be checked for movement, corrosion and sharp edges. Secure every weight with the approved clamps or bolts, and do not add or reposition ballast without confirming that the change complies with the event’s class rules and the vehicle’s structural limits. A modified vehicle carrying improperly secured weight is unsafe before the engine even starts.
After transport on a ute tray or trailer, repeat the inspection. Check ramps, tie-down points and the underbody for stone damage, and look for shifted weights after a long run across corrugated or gravel roads. Australian road transport rules cover load restraint, overhang, lighting and permits, so ensure that every adjustment remains legal for the trip home.
Measure tyre pressures when the tyres are cold and compare them with the vehicle’s established event settings. A hot tyre can read several units higher than its cold pressure, making an after-run check a poor guide for the next setup. Inspect the full circumference for cuts, bulges, exposed cords and damage from the pull sled. Check sidewalls for abrasion and make sure valve caps and wheel nuts are present.
Wheel studs and hubs should be checked for fatigue, especially on multi-axle trucks. Verify nut torque against the manufacturer’s figures and inspect the locking system where fitted. Do not paint the threads or apply anti-seize where it is not permitted, because it can change the friction and torque behaviour of the fastener. Look for blueing around the hub, a hot wheel or unusual bearing play.
Steering components need particular care on modified trucks and articulated tractors. Inspect drag links, track rods, ball joints, steering cylinders and hoses for leaks or abrasion. Clean away grease before it carries dust into the joints, while protecting the wipers on seals. Brakes should be free of oil and grease, and their lines should show no swelling or chafing.
Do not park with a hot vehicle pointed towards dry grass, particularly where the exhaust outlets sit low on a tractor. Give hot brake discs and exhausts space to cool, and confirm that the handbrake holds the vehicle on the event’s sloping run-off area. After the vehicle has cooled, repeat the wheel and steering inspection once more before loading it for the trip home.
The cab takes a beating from dust, vibration and repeated climbs in and out of the vehicle. Vacuum loose dirt from the floor, pedals and seat tracks before using damp cleaning products. Clean seat fabric according to its manufacturer’s instructions, and inspect the seat mounts, belt anchors and harness webbing for cuts, burns or chemical damage. Replace any safety item that has reached its expiry date or suffered impact loading.
Check the throttle, kill switch, reverse mechanism, indicators and emergency stop while the system is isolated as required. Do not lubricate a control that relies on friction for its normal function. Confirm that warning labels remain readable, the fire extinguisher is accessible and the cab’s fire-suppression system has not been left switched off after cleaning.
Exhaust pipes, manifolds and turbo outlets may carry oily residue. Clean these areas carefully with a suitable product, but protect yourself from hot surfaces and avoid using fuel as a degreaser. Radiator hoses, charge-air pipes and intake ducts should be checked for softening and cracks after repeated heat cycles.
Paint, chrome and polished alloy require a gentler approach. Wash grit away before applying wax or polish, because rubbing dirt into a finish causes scratches. Australian sunlight is harsh on paint and upholstery, so use a UV-resistant protectant and keep rubber seals conditioned where appropriate. A canvas cover or fitted shelter at home can reduce fading during storage.
Keep a maintenance record with the date, event, engine hours and work completed. Record fluid levels, tyre pressures, fastener checks and parts used, then add photographs of unusual wear or damaged components. This creates a useful baseline for the next pull and helps identify whether a problem is developing or was caused by one particular event or transport journey.
If you follow Great Lakes Truck and Tractor Pulling Association events, consult the association’s event calendar for schedules, locations and published updates. Australian pullers should also check with their local organiser, as class requirements, scrutineering procedures and event dates may differ between competitions. Keeping both calendars handy makes it easier to arrange servicing before travel becomes rushed.
Some pull followers also enjoy the betting side of the sport. Keep that interest separate from technical decisions: an anti-martingale betting strategy may describe a staking approach, but no betting system can determine whether a tyre, hitch pin or brake is safe. Place the money needed for essential spares, fluids and transport outside any entertainment budget.
Plan recurring work by engine hours as well as event dates. Filters, oil analysis, coolant testing, fastener inspections and belt checks may be due at different intervals. Carry a recovery kit containing sensible fluids, basic hand tools, tie-down straps, tyre-pressure equipment, a fire extinguisher and a mobile phone. A parts list built before leaving home is cheaper than a rushed purchase beside a closed servo late at night.
A clean and inspected vehicle is easier to load, diagnose and prepare for competition. At Australian pull days, teams often share tools, spare parts, mechanical knowledge and recovery equipment, especially when the nearest workshop is a long trip down the highway. Returning the vehicle to the paddock in good order also reduces the risk of fluid leaks, loose dust and unsecured tools causing trouble for another crew.
If you want to contribute beyond driving, look for practical ways to support the sport. The association’s ways to help page is a useful starting point for volunteering, event assistance and community involvement. Marshalling, scrutineering, helping in the kitchen, running errands or spotting recovery vehicles are all valuable roles. Reliable volunteers allow competitors to concentrate on their machines.
Before the next ute leaves the shed, set out a basic care kit and complete the post-event checklist: fluids checked, underbody clean, chassis inspected, tyres examined, safety gear reviewed and repairs recorded. Pack the spare parts you expect to need, secure the load and leave enough time for a careful walk-around before the trucks fire up next arvo. Make that routine part of every event so each pulling vehicle returns stronger, safer and ready for another run.
|
T
EST and TUNE
May 20th @ Dan Fair 1208 Sharpe Line, Cavan Contact Dan @ 705-930-4594 Food will be provided, so plan to attend |